Structural Fire Damage Cleaning in Hampton, SC
The drywall is gone, and now you are staring at blackened studs, scorched joists and a charred roof deck. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions puts you in touch with independent, licensed and insured Hampton contractors who clean the bare structure down to sound wood.
- Soda blasting, dry ice blasting and wire brushing
- Every stud and joist probed for char depth
- Sealer applied to lock in residual odor
Why the Bare Structure Needs Its Own Crew
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. This stage decides whether your rebuilt rooms smell fresh or smell burned for years.
Licensed & Insured Independent Pros
Each contractor on our referral list is an independent, licensed and insured local company. Verify both, and ask whether the crew follows the IICRC S700 standard for fire and smoke work.
Upfront Written Estimates
Media blasting depends on square footage, the media used and how hard the space is to get into. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
Day or night, a dispatcher picks up and starts looking for a structural cleaning crew right away. Timing depends on which crews near Hampton are free, and it is often the same day.
Blasting Rigs and Probing Tools
Structural crews bring soda blast pots, dry ice units, big compressors, HEPA vacs, air scrubbers and a sharp awl to test every member.
Do not climb into a burned attic or walk a scorched roof deck to look for yourself. Weakened joists and burned-through sheathing can give way without warning, and exposed wiring may still be live. Wait for the contractor to check that the structure is safe, and keep people off floors that sit over a burned crawlspace or basement.
Cleaning the Building From the Roof Deck Down
This is not contents cleaning and it is not debris haul-out. It is the work done on the wood, block, brick and steel that hold your house up.
Char Depth Probing and Member Decisions
Pressing an awl into the blackened wood shows how deep the char goes; a shallow crust over firm wood usually means it can be cleaned. When the char cuts deep into a joist or a truss web, the member gets sistered or swapped out.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Baking soda media knocks soot and surface char off framing while leaving the grain mostly intact. Expect fine dust and residue that has to be contained and HEPA vacuumed when the blasting is done.
Dry Ice Blasting
Dry ice pellets hit the surface and turn straight into gas, so there is no media left behind to sweep up. It works well in tight attics and around wiring, though it costs more and is noisy.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
For a few blackened studs or a small closet fire, wire brushes, sanding discs and a HEPA-shrouded grinder may be all it takes. It is slow on big areas but precise where blasting would be overkill.
Brick, Block, Concrete and Steel Beams
Porous brick, block and concrete trap soot deep in the surface, so crews use alkaline detergents, scrub brushes or blast media to lift it. Steel beams and columns are cleaned of soot and checked for warping or sag, which goes to the engineer.
Encapsulation and Attic Insulation Removal
Even well-blasted wood can hold faint odor in its pores, so crews roll or spray a pigmented shellac-based or specialty encapsulating sealer over cleaned framing. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Under the house, the crew probes the joists, sill plates and subfloor underside, then blasts and seals what can stay. Expect a vapor barrier to be pulled and replaced if smoke or hose water soaked it.
Ask your contractor which method they recommend for each area and why. A good crew may soda blast the open walls, dry ice the attic around the wiring and hand sand a few studs near the panel.
Plan for containment, because blasting throws soot and media into every corner it can reach. The crew hangs poly over doorways, masks off the HVAC returns and runs air scrubbers under negative pressure while they work. Ask how they will protect finished rooms and windows that were not damaged.
Looking at Blackened Studs and Rafters?
Phone our dispatchers and they begin searching for a structural crew close to Hampton. It costs nothing to call.
Call +1-833-336-1630The Path From Charred Framing to Sealed Wood
- 1
Phone the Dispatcher
Say which parts of the structure are open now, such as walls, attic, crawlspace, masonry or steel. Let us know if an adjuster, engineer or roofer has already visited.
- 2
Mobile Crew on Site
An independent crew shows up with its compressor, blast gear, poly and air scrubbers. They check that the roof and floor are safe to walk and that power to the open walls is off.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. You get a written, line-item quote listing square footage, method, sealer and insulation removal before any work starts.
- 4
Blasting, Sealing and Walkthrough
After blasting and HEPA cleanup, the framing gets its sealer coat, and you walk the bare structure with the crew lead. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
What Callers Said About Their Structural Crew
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. The crew pulled the insulation, dry ice blasted the rafters and rolled sealer on everything. An engineer looked at two deeply charred rafters and they were sistered instead of torn out.
My contractor brother-in-law said all the black studs had to go. The crew lead pushed an awl into each one and showed me the wood was solid under a thin crust. Soda blasting and a coat of sealer saved most of the wall.
The fire in our lower level left the block walls and the steel beam coated in soot. The contractor cleaned the block and the beam, then had an engineer check the steel for warping. No smell now, even with the windows shut.
Common Questions About Cleaning Charred Framing
How do crews decide if a charred stud can stay?
The test is simple: they probe it. An awl or screwdriver pushed into the black surface shows how deep the char goes, and wood that is firm just under a thin crust can usually be blasted and sealed. Deep char, cracks or a reduced cross section mean sistering or replacement, with a structural engineer making the call on anything questionable.
What is the difference between soda blasting and dry ice blasting?
Soda media is mild on the grain and helps with odor, though it leaves a white dust that needs a full HEPA cleanup. Dry ice pellets vanish on impact, so cleanup is easier and it works well around wiring, but it is louder and usually costs more. It is common to see both on one job.
Why seal the framing if it has already been cleaned?
Smoke gets deep into the pores of the wood, past what blast media can reach. A shellac-based or specialty encapsulant locks that residual odor in so it cannot off-gas through the new drywall. Sealer only works over clean framing, never as a shortcut over soot.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Loose-fill and batts act like a giant filter for smoke, and hose water often soaks them as well. Crews vacuum it out with a truck-mounted or portable insulation vac so the rafters and decking can be inspected and cleaned before new insulation goes in.
Can soot be cleaned off brick and concrete block?
Most of the time, but brick and block hold soot in their pores and need more than a wipe. Crews use alkaline masonry cleaners and stiff brushes, and soda or other media blasting for heavy buildup. Spalling or cracked masonry is a structural question for a mason or engineer.
Do I need a structural engineer for fire-damaged framing?
You may not on a small job, but any doubtful load-bearing member calls for one. An engineer's report on trusses, headers, beams, steel and badly charred joists protects you and supports the claim. Your local building department may also require one before the walls close.
Structural Fire Cleaning Throughout Hampton
Our dispatch line covers Hampton and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, crawlspaces, basements, garages and small commercial buildings are all in scope.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
Should the first contractor not suit you, ring us again and we will connect you with a different one. Get the bones cleaned before anyone hangs new drywall.
